Jump to content
Reliance Jio & Reliance Mobile Discussion Forums
ravjeet

Ruim Conversion For Ppc 6800

Recommended Posts

Procedure to convert ppc6800 to ruim .

1)remove back cover (4 screws) remove the thin sheet metal plate stuck on the pcb.

2) will see six points on the pcb .

3) solder sim tray on these points see direction of ruim card photo att . Remember we require the sim tray as per pin config att

4)solder jumpers as per photo att

5)cut the sheet metal sheet as to accommodate the sim tray.

6)as we have put the sim tray the original battery will not fit find extended battery cover and use it with standard battery .

7)upgrade radio to 1.47.01 .might have to unlock the pda to upgrade radio . Procedure can be found on net as titan unlocker.

8) in qpst change config to ruim if available can be done with cdma workshop free version also.

Phone is ready for reliance service use

photos.zip

Edited by ravjeet

Share this post


Link to post
Share on other sites

Fantastic!!! Thanks a lot for sharing this... have to get a PPC6800 soon ;)

Share this post


Link to post
Share on other sites

Finally wait is over :clap:

Gr8 work ravjeet and adisa :clap1:

by theway what is the backup capacity of dopod with this mobile.

Which version of mobile u have Sprint or versizon?

Share this post


Link to post
Share on other sites

check link below for battery spec it is 1500mah same as ppc6800 original.

there are some 1600mah battery also available of the same size for d810/htc3600.

modification can be done on any 6800 i have done it on sprint.

http://www.easy-battery.com/pda-battery/dopod-trin160.php

Finally wait is over :clap:

Gr8 work ravjeet and adisa :clap1:

by theway what is the backup capacity of dopod with this mobile.

Which version of mobile u have Sprint or versizon?

Share this post


Link to post
Share on other sites

This is really a great job. Hats off to ravajeet and adisa.

Share this post


Link to post
Share on other sites
check link below for battery spec it is 1500mah same as ppc6800 original.

there are some 1600mah battery also available of the same size for d810/htc3600.

modification can be done on any 6800 i have done it on sprint.

http://www.easy-battery.com/pda-battery/dopod-trin160.php

That's a clever workaround :praise:

Now I have wait for my PPC :Jeje:

Share this post


Link to post
Share on other sites

Rather then Going for LiION Battery Get any LiPolu Batteries for Replacements LiPoly is could be more thin and we can cut the Cover Plastic easily

Share this post


Link to post
Share on other sites

from where i can get a htc 6800?

and what is the price of htc 6800?

Share this post


Link to post
Share on other sites

BAD ESN Phones can be baught from Ebay.com @ $220

Share this post


Link to post
Share on other sites

Great job Ravjeet ! & thanks a lot for your help on yesterdays Work, configuring my phone!

:winko:

Share this post


Link to post
Share on other sites

^^^

Welldone my dear Ravjeet. Hats off to you.

Regards.

Share this post


Link to post
Share on other sites
Rather then Going for LiION Battery Get any LiPolu Batteries for Replacements LiPoly is could be more thin and we can cut the Cover Plastic easily

Do u mean back cover(which covers battary) of 6800?

Is it not possible to get a remolded back cover of PPC accomidating RUIM slot?

Edited by ss_rakesh

Share this post


Link to post
Share on other sites
Rather then Going for LiION Battery Get any LiPolu Batteries for Replacements LiPoly is could be more thin and we can cut the Cover Plastic easily

Do u mean back cover(which covers battary) of 6800?

Is it not possible to get a remolded back cover of PPC accomidating RUIM slot?

I think if one goes to FRP molder, he can mold FRP covers. Fiber Reinforced Plastics can me made in any color, with very high gloss. (Helmets are made from FRP).

Making wood mold may cost less than 750 buck. I will suggest RIMWEBIANS who are interested in buying 6800 from US, ontribute some money to person who has 6800 and he can get covers made and then gives covers at cost or add little profits to cover his out of pocket expenses. Covers can be as thin as 1.5 mm

Edited by kshah

Share this post


Link to post
Share on other sites

LiION Battery Contains Cell with Liquid so to Protect it a Hard Metal Cell is Needed but in LiPoly which only have High Quality Polymer dont need Metal Casing so it will be more Thin and its Cell can be Unassembled from to Better accommodate into PPC6800

Kalpak Idea to Rather go for New Back Cover is Best I have PPC6700 with Extended 2100 mah Battery which have 2x Thick Battery with Customised Back Cover so With in Next 2 Month we will see Extended Battery for 6800 with Extended Battery Cover also.

Share this post


Link to post
Share on other sites

Yes, I prefer spending money on molded cover insted of disturbing battery.

Also I am not sure, rather using battery sujjested by ravjeet, If I try to use standard battery for 6800 with molded backcover,

Since from the design of 6800, there is no space b/w battery and board.

Does battery sit properly over the board contacts, after soldering RUIM slot?.

If this no prob then it is gr8.

Sideo already has std and extd Lipoly batteries for 6800.

http://www.seidioonline.com/index.asp?Page...&ProdID=814

http://www.seidioonline.com/index.asp?Page...&ProdID=888

Edited by ss_rakesh

Share this post


Link to post
Share on other sites

http://www.seidioonline.com/index.asp?Page...&ProdID=797

http://www.seidioonline.com/index.asp?Page...&ProdID=827

We can use Hard Case Compatible for Slidding then we could Remove Original Cover which will allow use to use SIM / RUIM

This is an Interim Idea !!! Untill we get Compatible Battery or Back Cover :biggrinthumb::clap1::clap::thumb:

Edited by hetaldp

Share this post


Link to post
Share on other sites

Its really a happy news that we can use PPC 6800 with Reliance which RUIM enabled.

So now whose gonna take the authority to import to India and make it RUIM enabled and seel it...... Sadik bhai... come on... U cant sit idle....

sadik bhai and hetal has to do something to help us.........

make its fast.... make it available for common man like us..

Share this post


Link to post
Share on other sites

If some one donot want to get a cover remolded I beleave they can buy for a cover for extended battery, Solder the RUIM & use the standard battery with some cushioning.

Too many ways :) , waiting to hear if someone else converted their 6800 to RUIM

Share this post


Link to post
Share on other sites
http://www.seidioonline.com/index.asp?Page...&ProdID=797

http://www.seidioonline.com/index.asp?Page...&ProdID=827

We can use Hard Case Compatible for Slidding then we could Remove Original Cover which will allow use to use SIM / RUIM

This is an Interim Idea !!! Untill we get Compatible Battery or Back Cover :biggrinthumb::clap1::clap::thumb:

look my attach !

New_Folder.rar

Share this post


Link to post
Share on other sites

wow ! a breakthrough achievement. .. im waiting for some one to do the importing,programing,soldering stuff and make it ready to use with just inserting an ruim card left .

guys who are thorough with the things can have some deals over here and ultimately help everyone to get the phone .!

cos not everyone are goin to do the things of soldering n programing.

Share this post


Link to post
Share on other sites

@Niral Sutaria

Work is still half done Ravjeet and other co members are still working on the battery issues !!

Lets hope some solution comes up soon ... !!

Share this post


Link to post
Share on other sites

@adisa

Thanks buddy !!

but may i know why do u love me ?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×