Jump to content
Reliance Jio & Reliance Mobile Discussion Forums
Mufaddal

How To Get Data On Palm

Recommended Posts

@hitesh : I havent buy from rimweb i even tried 000000 its showing enter correct spc.

I am using 1.41 OS

@ami1 : Can u give me the link from where i can reset spc code

Share this post


Link to post
Share on other sites

I am getting the following error

root@castle:/# novacomd socket was closed prematurely

novacom: unexpected EOF from server

Any clues?

Share this post


Link to post
Share on other sites

^^^^

Can U on DEV mode

Share this post


Link to post
Share on other sites

Development Mode is on

Diag Mode on on USB 1

Share this post


Link to post
Share on other sites

Put Diag TO NONE

Share this post


Link to post
Share on other sites

new problem occurred when i was performing those step

now when i m trying to connect my device to computer its just getting charge but no usb options :(

Share this post


Link to post
Share on other sites

If your usb mode is set to serial port then you can connect qpst/qxdm/unicdma etc BUT you will not get charging/usb-drive options & neither will NovaCom or any linux commandline work.

If your usb mode is set to none then you will get charging/usb-drive/media-sync etc options and you can get linux commandline with novacom or WOSQI (webos quick install) BUT qxdm/qpst/unicdma won't connect (since they need serial port)

So you need to switch usb-mode to serial when you need to program with qpst etc and otherwise keep it at None so that you can get usb-drive WOSQI novacom etc.

Hope, its clear now.

Share this post


Link to post
Share on other sites

Put Diag TO NONE

I have tried that.. does not help..

tried putting developer off and again on.. just in case..

Any other clues?

Btw, it worked perfectly fine a few days back!

Share this post


Link to post
Share on other sites

^^^^

Put your phone to Diag NONE Which is on the USBPass through mode

And select JUST charge Option

Afer connect Your phone to novacom and write: mpt 0d

Share this post


Link to post
Share on other sites

Thanks Vijay..

But thats exactly what I am doing

Developer Mode On

USB Pass Off on all ports

Go to command prompt

novacom -t open tty://

which responds well

but when I say

mpt d userserial

It says

root@castle:/# novacomd socket was closed prematurely

novacom: unexpected EOF from server

Share this post


Link to post
Share on other sites

^^

Try using Nova Shell

When connect type mpt 0d

With this u could access serial mode.

Download novashell from Here

Share this post


Link to post
Share on other sites

Check if its userserial or userial - just type mpt and it'll give the syntax or mpt --help

BTW, the mpt command is only to put it in serial mode, if you are using usb mode app to put in serial or none mode then no need of mpt cmd

Share this post


Link to post
Share on other sites

Actually I am unable to connect in USB Diag mode I always use Serial Mode,

My phone not detect drivers of Diag mode,

Share this post


Link to post
Share on other sites

Are you on windows 7? Possibly after this error, your phome may be in diag.

Share this post


Link to post
Share on other sites

How to go to usb pass through mode to set all ports to None in 1.4.5 OS Verizon bypass ROM?

##USBPASS# does not work.

Share this post


Link to post
Share on other sites

How to go to usb pass through mode to set all ports to None in 1.4.5 OS Verizon bypass ROM?

##USBPASS# does not work.

Dial ##8727277# instead of ##usbpass# and you will get access to the menu for setting all ports to None.

Share this post


Link to post
Share on other sites

##8727277#

For usb pass through.. If not work install usbpass apk files by webosQI,

Share this post


Link to post
Share on other sites

Dial ##8727277# instead of ##usbpass# and you will get access to the menu for setting all ports to None.

Thank you. This worked. 000000 Diag Authorization code doesn't work. This phone I bought from rimweb only. @Hitesh

Share this post


Link to post
Share on other sites

Dial ##8727277# instead of ##usbpass# and you will get access to the menu for setting all ports to None.

Thank you. This worked. 000000 Diag Authorization code doesn't work. This phone I bought from rimweb only. @Hitesh

to unlock ##usbpass#, u need to run 'prepassthroughkeygen', which you can get from Hitesh's post, or by googling for 'prepass gen'

Share this post


Link to post
Share on other sites

Feels like this palm is very complicated

  • Like 1

Share this post


Link to post
Share on other sites

USB Pass thru auth code is no your SPC

I have posted and mailed you the link for code generator, this code is device specific.

let me know if not working.

Share this post


Link to post
Share on other sites

Thanks Hitesh. Yes it works perfectly and novacom and hence my PC is again able to see my Pixi

I am getting the same error that @Bablus is getting. Is the problem solved @Bablus? There is no update from you from then.

Edited by deepakchan

Share this post


Link to post
Share on other sites

^^

Deepak U post ur problem in only single thread not in multi thread ?

What exactly problem u have faced?

Share this post


Link to post
Share on other sites

@Deepak:-

you dont require that command if your diag mode is working,

use the usb passthru and make USB1=DIAG and all other to none or disabled.

then check in device manager in windows. it should show com port if drivers are installed.

Share this post


Link to post
Share on other sites

Deepak U post ur problem in only single thread not in multi thread ?

What exactly problem u have faced?

Sorry I shall stick to this thread from here on.

@Deepak:-

you dont require that command if your diag mode is working,

use the usb passthru and make USB1=DIAG and all other to none or disabled.

then check in device manager in windows. it should show com port if drivers are installed.

Thanks Hitesh. I shall check this and also vijay's post of using mpt 0d and get back to the forum with the exact problem if any.

In the first step of the 2nd portion of the procedure, opening up qpst, how do I do that? I am presented only with these after unzipping the qpst package.post-42092-0-53330800-1289387499_thumb.p

Also ananth001 has sent me a .qcn file from a working Tata pixi plus with data. I do not know where to use this too. post-42092-0-17629000-1289387683_thumb.p

Edited by deepakchan

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×