Jump to content
Reliance Jio & Reliance Mobile Discussion Forums
anvaralicp

Guide: Unlock LG Spirit MS870 MetroPCS To Work With OMH CDMA SIM

Recommended Posts

LG Sprit ms870 metro PCS can be unlock to use any CDMA OMH, tested with reliance Data and Voice working

Steps

1. Calculate the SPC code using the calculator attached

2. Install the driver attached

3.connect usb as LG software mode and debugging enabled

4.Open DFS

5.send SPC

6 Change mode to RUIM only and write then restart the phone

7. Voila , ur LG Spririt is OMH ready

LG Driver

https://www.dropbox.com/s/fmk7o46gov8k76o/LG-Mobile-Driver_v3.10.1.exe

MetroPCS MSL_SPC Code Calculator.rar

  • Like 8

Share this post


Link to post
Share on other sites

Gud work

Sent from my GT-N7100

Share this post


Link to post
Share on other sites
Can be done faster and easier.

With the free version of DFS:

1. Open DFS, select the port

2. Go to "General" tab - Click "Read SPC"

3. Go to "General" tab - "SPC calculator"

4. Send SPC and change :)


post-85856-0-44548300-1402827464_thumb.p

Share this post


Link to post
Share on other sites

SPC will not read in DFS, u can use the calculator attached commom for all MetroPCs

Share this post


Link to post
Share on other sites

SPC will not read in DFS, u can use the calculator attached commom for all MetroPCs

It will not read but metro spc calculator is in build in DFS

Sent by Moto G on Reliance CDMA

Share this post


Link to post
Share on other sites

SPC will not read in DFS, u can use the calculator attached commom for all MetroPCs

lol

Same SPC)

post-85856-0-60546500-1402906991_thumb.j

Share this post


Link to post
Share on other sites

LOL, i never noticed that, im doing first time with MetroPCS, thanks

Share this post


Link to post
Share on other sites

Ok, so it looks like my driver installation was not properly done and the actual diagnostic port was not visible in DFS. I retried and can see all phone info in DFS with 'LGE AndroidNet USB Serial Port (COM10)' connected. A 6-digit SPC is calculated. I manually entered the SPC on top left and clicked 'Send SPC'. The log says DEVICE UNLOCKED. I also changed the Ruim Config to 'RuimOnly' in Programming>General>Config section and clicked 'Write' next to it. But when I restart the phone with Reliance CDMA SIM it still says INVALID SIM.

Can someone please clarify the next steps in little more detail (step by step with screenshots)? I am not sure if I followed all required steps correctly.

Share this post


Link to post
Share on other sites

@crusader2015 try to change RUIM Preffer in DFS

Share this post


Link to post
Share on other sites

@vijaymalhotra_2007 - Can you please guide where can I find & change the "RUIM Preffer" in DFS? I can see RUIM CONFIG under Programming>General section which has 'RuimPref' as one of the values in drop down. Should I just select this & click 'Write' next to it?

Thanks in advance.

Share this post


Link to post
Share on other sites

Thanks @goodlogic. That did the trick. I have tested TATA CDMA SIM successfully, will check RIM in a while.

Share this post


Link to post
Share on other sites

Does evdo work on it as i get only 1x on this mobile while evdo work on other handset.

Any idea to get evdo.?

Sent from my GT-S5360 using Tapatalk 2

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


×